Another status update

With today’s ready-packed devices, now 34 blueReaders have been shipped and actually one has already been exchanged.

All who are waiting now: It’s going forward! Every day we are getting slightly better, find new details in production and continue to optimize!

Actually, we had hoped for 5-10 devices a day, but unfortunately we do not make it yet :/ Why?


  • Problems in potting and a possibly poor batch of silicone have generated almost 30 damaged blueReaders we needed to unpack and prepare for another round..
  • Due to too much use of release agents during soldering, components on almost 20 boards were damaged, all had to be checked manually and defective components replaced.
  • Poor pigments have led to bleed out of colors from some blueReaders.
  • A few changed details in the components of the blueReader, which help us to improve the current flow while charging, required a revision on nearly 40 blueReader boards and almost all wireless loader boards that had already been manufactured.

So as always: plenty to do 🙂

Also at the software I am still working on, unfortunately still not completely presentable, but hopefully more in the next days …

The current state is that we still have problems with few devices on Android 7. However, it is still not quite clear whether there are errors in xDrip+ or the Android or something else. But we’re working on it!

Number One…

Without to much words:

The package list for the first has been completed!


and labeled with the all you can eat label package  🙂

The first boxes will start the journey tomorrow to Germany, Switzerland, Slovakia and to England! I also hope that I get the order system adjusted today to send the tracking codes to the first customers!

What is in the box?

1x blueReader colored as ordered (and with or without magnets)

1x wireless Charger, in the ordered color

1x Micro-USB-Kabel if chosen

1x Short manual in german and english: blueReader short manual

1x Holder v3: same color as the wireless charger.

I hope this increases still a little more the anticipation 🙂

MIstakes found…

A week search is now behind me, but I have found crucial errors.

Now the delivery is close!

What was going on this time?

  • Saving energy on the edge of the game has a massive impact on the stability of the chip.
  • There are many possibilities to realize uart communication on the chip, but apparently only one that really works.

The result is a much slimmer and faster firmware which unfortunately needs more energy as I had hoped (in comparison to the last post), but still low enough to have probably energy for up to 7 days. The energy levels of this one measurement described in the last post could not be reached again, unfortunately. But if the tests are good, and up to 7 days are possible, this is still a very good result in my opinion, especially if the runtime is reproducible.

Now comes the finishing touches for the transfer of the commands and the devices will go into shipping. I will avoid a longer test period, since  the firmware can be renewed at any time via a mobile phone. 🙂

The final sprint is here!

View of the work…

First a small look at the desk:

A debugger for the chargers is one of the latest achievements that the 3D printer has printed for me.

But why a debugger for the chargers?

The chargers also have a very small microprocessor to generate the oscillation for the charging field and to control the LEDs. And they do have an interface which enables me to look at charging process and to determine if that board and blueReader are matching. Tiny variations in the tilt of the charger and receiver coil can have a huge impact on the charging process.

In the background you can see the first batch of blueReaders currently being tested for more unexpected hiccups.

Meanwhile, even the assembly of the blueReader has got revision numbers and we are already at version 31 of the instructions to build a finished blueReader, starting with the board.

The last important changes were:

  • Pre-encapsulation of the batteries to avoid air bubbles on the side which can arise from the protective electronics.
  • The soaking of the board in cold (thus non-hardening) silicone before the actual pouring to get the air out from under the components and especially under the shield of the Bluetooth module.
  • The gluing and laminating of the antenna to avoid breaking.
  • Use a silicone adhesive to connect the antenna to the battery, the battery to the board and the charging antenna to the board.
  • Adding another blot of silicone adhesive on the opposite side of the loading antenna to prevent the board from sinking one-sidedly.
  • Replacing the charging antenna against a much larger one without increasing the size of the blueReader.
  • The pre-coating of the magnets with an adhesive base for the silicone to avoid a detached silicone layer over the magnet.
  • The punching of the antenna to achieve a better connection of the silicone layers.
  • Minor changes in the electronic parts which lead to a lower power consumption and easier assembly of the board.

This list can be made at least twice as long and omits the developed tools, forms and components, or the list of the added test procedures. The complete list, the construction manuals, the molds and tools will be published anyway! So a little more patience for those who are interested.

At the moment, there are daily conversations between my engineer and myself to avoid any further problems. But the tests so far are very promising and we continue the production and testing until further notice. Currently our capacity is about 5-10 devices per day. Unfortunately this is depends very much on the amount of bubbles in the silicone, how long and frequently this must be vacuumed that al less bubbles es possible are put into the blueReader.

Finally, the tension is relieved, now we focus on production and verification!




What’s wrong with us?

Where are the devices?

We were stopped. The first devices came from the production and were tested by me…

The result: many broken blueReader :/

  • blueReader can be frozen, but not too deep, otherwise the battery will suffer permanent damage.
  • blueReader can be baked, but also not too hot.
  • blueReader can be folded, but that destroyed it.

What they can be destroyed by folding? What happens there???

Unfortunately, the paths of the antenna break as soon as the blueReader are folded to much.

The last days we have therefore intensively researched, tested and tweaked the blueReader’s design. The result is a packaged antenna and a slightly modified design:
In addition, we were able to significantly improve the charging system and provide more energy in a shorter time.
The new antenna design now consists of a laminate of two plastic films and a stiffening layer of plastic around the antenna. In addition, the design of the silicone hull has been slightly modified to exert less pressure on the antennas traces.

But what about the freezing and baking? To look at the safe operation parameters of the blueReader I’ve put several in the fridge and into the ice compartment, two into boiling water and several into oven at different temperatures.

The result:

  • At about 60° Celsius the battery starts overheating and puffs up.
  • At about 70° Celsius this state becomes irrevisble and the battery loses its power.
  • Below 10° Celsius the battery loses its power really fast (Energy gets converted to heat).
  • Below 0° Celsius the battery starts to freeze and loses most of its power.
  • Below about -10° Celsius the battery dies and can’t be recharged any more.

Under no circumstance I have so far managed to destroy the battery in a way that it broke up in flames or leaked  🙂

What is next?

Currently the new molds are being built and the blueReader, which have so far been cast, are being equipped with new batteries and improved antennas. Hopefully we can test them in the next days 🙂

Forward, backward, upwards!

It continues…

A few new attempts for a holder for the night or sport are finished and almost all have missed the mark… Still the pile is not as big as with the charger cases.

Finally, one good result was finished in the end: In comparison again to the best prototype so far:And on my arm: After one night is the best one I have done so far. The sensor is not under pressure, but the blueReader is also safely kept in place, even against the evil forces of the bedspread and turning around. One of the first long nights (with turning around 5 times around in the bed) where no alarm came because of missed values!

Also the production of the housing goes ahead: One housing after another falls out of mold and after Easter it will have the first completely finished chargers.

With the rest, I’m still waiting for parts again, but after Easter it should go on there too! Currently over 100 blueReaders are in the different production steps 🙂

Another update…

Today a little more relaxed update from me…

Now that the ordering system is online and I have cleared many big and small things, it goes on with fresh strength!
Only 28 coupons are not used yet!

Currently, about 100 blueReader are in production and will be shipped in the next few weeks. As soon as we have a device ready, and it has passed all tests, an email will be sent to the recipient that their order is now processed and thus can not be changed. Until then, you can decide as often as you like, the coupon key is tracked through orders and cancellations!

The charger has also a few news: Since I was just preparing new molds, I came up with the idea of ​​not printing in plastic but wood … Well not real wood, but wood filament which reminds more of pressboard than of wood, but it smells good:  At first sight it looks not so great, but you can grind it and fill with wood glue 🙂

The final prototype made of plastic generated this result:
especially on the inside it looks quite rough.

The wooden mold with wood glue smoothed and polished: 

Already better, but also not quite the maximum…

But wood can be painted, much better than the printed plastic: now the sides cast reflections too and it finally looks as I imagined. Even the silicone shape makes a completely different impression:

The only pity: I already had about 40 cases prepared, but they go now into the garbage, the new cases are just so much nicer and the expenditure for the production of the housing is also not so high (stir, pour, wait, demold)!

It took me a long time…

It took much too long to my taste, but now all coupons are send to the supporter!

Please check if you got your key and if not, please contact me with your full name and the email address where you registered with startnext at

The first devices are now in production and we hope to get about 80 devices ready before Easter and get them into shipping. Then my engineer will have 2 weeks of holiday … this seems necessary 🙂

The stone…

…which blocked my way for long enough is finally rolling!

Because of the two companies and the amount of unfinished tasks in both I have suffered considerably under burn out in the last weeks :/

But now I have progressed on many tasks and here we go again!

The order page is available now 😀

You can now pre-order blueReader at ! All participants in the Crowdfunding campaign will get their keys starting tomorrow to order their devices!

The allocation will be made according to a very simple principle:

  1. First the supporters get the devices they order.
  2. If one variety is available in excess, the pre-orders get the possibility to buy the blueReaders.
  3. Every blueReader costs 225 EUR, including shipping and taxes.

So much for today, tomorrow is all about the keys and later I have more details about the software, apps and all the rest 🙂


A small update to the current status:

  1. The start of the production is almost finished 🙂At the moment, I produce housing parts and blanks for casting molds so that we can now pour very quickly a larger quantity of devices.Every 20 minutes one housing and two forms are finished.
  2. I have made progress on the attachment
    This is the result 🙂 Currently we try with silicone waste whether it works better from plastic or silicone. As soon as we are able to make a decision, I will show the different variants and what we think is the best solution.
  3. Magnets The first devices with magnets have gone into the test. Everything works great, but the devices are about 1mm thicker than the devices without magnets. It is strong enough to handle most everyday situations, but you can easily loose it while handling a backpack or by turning in your bed.
  4. I am currently working on the order system with high pressure
    It should have been online since the weekend, but I also underestimated this task…

What is next?

Once the order page is online, all supporters of the Crowdfunding Campaign will be able to order their blueReader. First the one who ordered prototypes and then the people who ordered series devices.

Every person can freely choose whether they prefer a series or prototype blueReader (or mixed, if you have paid for several).

In addition, the rest has the possibility to pre-register for devices. This is not a binding purchase! Once the requested devices are ready, you will be given the option to pay them via the website (via PayPal).